Known Issues

1. SIP ALG will cause problems if it's enabled, but it can be disabled on at least one of the firmware versions.
2. MTU is set to Auto by default, which can set it to 576, which is too low.  This will cause intermittent phone feature failures & call audio (RTP) to be lost mid-calls.
3. We need more information on this router to find out if the other basic router requirements can be made on this router. 
   • Please contact UNIVERGE BLUE® Voice Technical Support so we can better document other necessary changes that need to be made to this router.

Resolution

1. Log into the router.
2. Go to Firewall > Basic Settings > SIP ALG > Uncheck > Save. 

   *This has changed on firmware v.1.0.6.6 and later. Now Go to Firewall > Advanced Settings > SIP ALG > SIP ALG > Uncheck "Enable" > Save. 

   • If there isn't an option to disable SIP ALG, the IT or a tech-savvy individual will need to call Cisco for help upgrading the router to the latest firmware version.
   • If the router is running the latest firmware and it still doesn't have the option to disable SIP ALG, then you will need to replace the router with a compatible one.
3. Change the MTU from Auto to one of the options below.
   
   • This setting is usually found under Networking > WAN.
   • Your router may reference 'WAN' as Internet Settings or with slightly different terminology, depending on the firmware:
     
     • 1500 for Cable
     • 1492 for DSL
     • FiOS using PPPoE (most pre-2006 FiOS circuits) – 1492
     • FiOS using DHCP (most post-2006 FiOS circuits) -- 1500
     • Contact your ISP if you're unsure.
4. This step is only needed if you have or plan to purchase Polycom phones.
   
   • The steps below only apply if you are using the RV220W as the DHCP server:
     
     • Go to Networking > LAN > LAN Configuration > Set the following:
       

       *This has changed on firmware v.1.0.6.6 and later. Now Go to Networking > LAN > IPv4 LAN 

       • Primary DNS Server - "8.8.8.8".
       • Secondary DNS Server - "8.8.4.4".
       • LAN Proxy - DNS Proxy - Uncheck.
       • Click Save.
5. This optional step is needed for call quality monitoring and troubleshooting purposes:
   • Go to Firewall > Attack Protection > Enable Respond to Ping on WAN (Internet) > Save.
   • Note: Leave all other firewall settings on this page unchanged. 
     
     • The Firewall, SPI, and DoS protection do not need to be disabled.
6. If QoS options are available in your particular firmware version, the following steps can be taken:
   • Go to QoS > WAN QoS Profiles and set:
     
     • WAN QoS - Enable
     • WAN QoS Mode - Priority
     • Leave Priority Bandwidth Allocation settings at default
     • Click Save
   • Go to QoS > WAN QoS Profiles > WAN QoS Profile Table
     • Click Add
     • Enter name "Cloud_Voice" with Priority "High"
     • Click Save
   • Go to QoS > Profile Binding
     • Click Add
     • Available Profile - Cloud_Voice
     • Service - ANY
     • Traffic Selector Match Type - IP Address Range
     • Starting IP Address: You will need to enter the IP address that pertain to the VoIP product being used. Please contact UNIVERGE BLUE® to obtain the necessary IP address.
     • Ending IP Address: You will need to enter the IP address that pertain to the VoIP product being used. Please contact UNIVERGE BLUE® to obtain the necessary IP address.
     • Click Save
7. We need more information on this router to find out if the other basic router requirements can be made on this router. 
   
   • Please contact UNIVERGE BLUE® Voice Technical Support so we can better document other necessary changes that need to be made to this router.